BIOS

Reset Your BIOS to Default Settings (Clear CMOS)

5 minsEasyTools neededVideo coming soon

The CMOS is a small block of memory on your motherboard where your BIOS settings are kept. Clearing it returns those settings to their defaults, and it's an easy way to fix a range of PC issues.

Tools needed

  • Screwdriver
  • Non-conductive tool

Battery safety

WarningThere's a lithium button/coin battery in this product. If it's swallowed or put in any part of the body, severe or fatal injuries can happen within 2 hours. Store new and used batteries well out of children's reach. If you suspect someone has swallowed a battery or placed one in any part of their body, get medical attention immediately. For fast expert advice, call 13 11 26 to reach the Australian Poisons Information Centre (24/7).

When should you clear the CMOS?

Clearing the CMOS is useful for:

  • troubleshooting hardware problems
  • putting BIOS/UEFI settings back to their defaults
  • fixing boot problems
  • recovering from a failed overclock.

How you do it depends on your motherboard, and there are a few options. Pick the method below that matches yours.

TipFor instructions and precautions specific to your board, always check your motherboard's manual.

Method 1: Use the CMOS jumper

On most motherboards you'll find a CMOS jumper, normally labelled CLR_CMOS, CLEAR or RTC.

  1. Step 1 of 4

    Turn off your PC

    Turn off your PC, then disconnect it from the wall power.

  2. Step 2 of 4

    Find the CMOS jumper

    Your motherboard manual shows exactly where the CMOS jumper is, so look it up there.

  3. Step 3 of 4

    Short the pins

    With some motherboards, all it takes is touching a metal object, like a screwdriver, across the two pins to short them. Keep it in contact with both pins for 5–10 seconds.

  4. Step 4 of 4

    Power on

    Reconnect the power and switch your PC on to see if the problem has gone.

Method 2: Remove the CMOS battery

The CMOS battery powers the CMOS chip so it can remember your BIOS settings. Removing it for a while clears them.

  1. Step 1 of 7

    Turn off your PC

    Turn off your PC, then disconnect it from the wall power.

  2. Step 2 of 7

    Open the case

    Open your PC case so you can reach the motherboard.

  3. Step 3 of 7

    Find the CMOS battery

    Look for a small, round, coin-shaped battery on the motherboard.

  4. Step 4 of 7

    Remove the battery

    Lift the battery out carefully, easing it free with a non-conductive tool.

  5. Step 5 of 7

    Wait 5–10 minutes

    Leave the battery out for 5–10 minutes to make sure the CMOS memory is cleared.

  6. Step 6 of 7

    Put the battery back

    Put the battery back in its holder.

  7. Step 7 of 7

    Power on

    Reconnect the power and switch your PC on to see if the problem has gone.

Method 3: Use the BIOS/UEFI menu

On some newer motherboards, you can clear the CMOS settings from within the BIOS/UEFI itself.

  1. Step 1 of 4

    Enter the BIOS/UEFI

    Restart your PC. While it starts up, press the BIOS/UEFI setup key (most often Del, F2 or Esc).

  2. Step 2 of 4

    Find the reset option

    Browse the BIOS/UEFI menus until you find an option such as Load Default Settings, Reset to Default or Clear CMOS.

  3. Step 3 of 4

    Select the reset option

    Choose that option, then confirm when asked.

  4. Step 4 of 4

    Save and exit

    Save the changes you've made, then leave the BIOS/UEFI.

Method 4: Use the reset button (if your board has one)

Certain motherboards have their own button just for resetting the CMOS.

  1. Step 1 of 4

    Turn off your PC

    Turn off your PC, then disconnect it from the wall power.

  2. Step 2 of 4

    Find the reset button

    Look for the CMOS reset button on your motherboard. It normally has a label and may light up.

  3. Step 3 of 4

    Press and hold

    Push the reset button and keep holding it for roughly 5–10 seconds.

  4. Step 4 of 4

    Power on

    Reconnect the power and switch your PC on to see if the problem has gone.

What's next?

Once you've cleared the CMOS, watch how your PC behaves to make sure everything is working as it should. If the problem is still there, try some more troubleshooting or contact us for help.

This guide can help with

Need a hand?

If you're still stuck or want a second opinion, get in touch. Our team is always happy to help.