Inside the case

Check the Cables Inside Your PC

5 minsEasyVideo coming soon

For your PC to run at its best, every cable inside it needs to be fully and correctly seated. Cables can sometimes work slightly loose in transit, so this guide walks you through checking that everything is firmly connected.

Why check the internal cables?

Checking your internal cables helps you get:

  • Stable power delivery: your parts receive steady, consistent power.
  • Reliable data transfer: cables that are seated correctly stop data from dropping out.
  • System stability: your PC stays stable and runs the way it should.

Get your PC ready

  1. Step 1 of 2

    Shut down and unplug

    For your safety, turn your PC off and disconnect it from the wall before you start.

    WarningBefore reaching inside, check that the PC is fully switched off and the power cord is out. This protects both you and your parts from harm.
  2. Step 2 of 2

    Remove the side panel

    Take the side panel off your case. On most cases, you either undo a few screws or slide the panel out.

Check the main power cables

With the PC powered off, press firmly on the plastic frame of the connector of each of these cables (not the wires).

  1. Step 1 of 3

    24-pin main power cable

    The large 24-pin main power cable sits along the motherboard's right-hand edge. Find it there.

    Press firmly on the connector's plastic housing and check that its latch has locked into place.

  2. Step 2 of 3

    CPU power cable

    Look in the upper left-hand area of the motherboard to locate the CPU power cable.

    Press firmly on the connector's plastic housing. Listen for a click, which means the clip has locked firmly into place.

    Good to knowOn some motherboards you'll also find an extra 4-pin power connector in this spot. If you see one, check it in the same way.
  3. Step 3 of 3

    GPU power cables

    Locate the GPU power cables. They're usually on the graphics card, near its right-hand end.

    Press firmly on each connector's plastic housing. Listen for a click, which means each clip has locked firmly into place.

Check the other cables

  1. Step 1 of 4

    Cable sleeves (if fitted)

    Cable sleeves are braided extension cables that give a neater look than standard black plastic cables. If your PC uses them, make sure they're plugged in all the way.

    Take off your PC's rear panel. Follow each sleeved cable back to the point where it joins a power supply cable, then press firmly on each join so it's fully connected.

  2. Step 2 of 4

    Modular power supply (if fitted)

    Locate the power supply. It sits at the back of the case, either up the top or down the bottom.

    For any connectors within easy reach, gently press them in towards the power supply so you know they're fully clicked in.

    TipStick to the connectors that are easy to get to. Don't force anything, and don't squeeze your hand into cramped areas.
  3. Step 3 of 4

    SATA cables (hard drives and SATA SSDs)

    Every SATA drive uses two cables: a data cable and a power cable.

    • Locate the drive inside your case. You'll usually find drives in bays near the base of the case or fixed to the back.
    • Make sure both cables are plugged into the drive, then press each connector gently into the drive so it's secure.
    • Follow the data cable to the point where it joins the motherboard, then press that connector firmly into its socket.
  4. Step 4 of 4

    Fan cables (PWM and ARGB)

    RGB fans use two connections: PWM supplies power and ARGB controls the lighting. Non-RGB fans use PWM only.

    To keep cabling simple and neat, every fan in our builds connects to a hub mounted at the rear of the PC. The ARGB lighting connectors sit on one side of the hub and the PWM power connectors sit on the other. Systems with more than 6 fans may have two hubs.

    • Make sure nothing is missing from the hub, and press each connection firmly into place to secure any that are loose.
    • Follow the hub's cable to the point where it joins the motherboard, then press that connector firmly into its socket.
    • Also check that the hub's SATA power connector is plugged in all the way.

What's next?

When every internal cable is checked and secure, put the side panel back on, reconnect the power and switch your PC on to confirm it all works as expected.

This guide can help with

Need a hand?

If you're still stuck or want a second opinion, get in touch. Our team is always happy to help.